California Instruments 801RP Series Manual de usuario Pagina 103
- Pagina / 223
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MX / RS Series SCPI Programming Manual AMETEK Programmable Power
MX / RS Series 103
4.21 Source Subsystem - Pulse
This subsystem controls the generation of output pulses. The PULSe:DCYCle,
PULSe:PERiod, and PULSe:WIDTh commands are coupled, which means that the values
programmed by any one of these commands can be affected by the settings of the others.
Refer to Table 4-1 and Table 4-2 under PULSe:HOLD for an explanation of how these
commands affect each other.
Subsy
stem Syntax
[SOURce:]
PULSe
:COUNt <n> | MAXimum Selects transient pulse count
:DCYCle <n> Selects pulse duty cycle
:PERiod <n> Selects pulse period when the count is greater than
1
:WIDTh <n> Selects width of the pulses
:HOLD WIDTh|DCYCle Select which parameter to hold during programming
PULSe:COUNt
This command sets the number of pulses that are output when a triggered output transient
occurs. The command accepts parameters in the range 1 through 2E8. If MAXimum is sent,
the output pulse repeats indefinitely.
Command Syntax [SOURce:]PULSe:COUNt<NRf+>
Parameters 1 to 2E8 | MINimum | MAXimum
*RST Value 1
Examples PULS:COUN 3
PULS:COUN MIN PULS:COUN MAX
Query Syntax [SOURce:]PULS:COUNt?
Returned Parameters <NR2>
Related Commands PULS:DCYC PULS:PER PULS:WIDT
PULSe:HOLD
This command specifies whether the pulse width or the duty cycle is to be held constant
when the pulse period changes. The following tables describe how the duty cycle, period,
and width are affected when one parameter is set in a single program message. if two or
three parameters are set in a single message, there sequence will define how they will be
affected.
Command Syntax [SOURce:]PULSe:HOLD<parameter>
Parameters WIDTh|DCYCle
*RST Value WIDTh
Examples PULS:HOLD DCYC
Query Syntax [SOURce:]PULSe:HOLD?
Returned Parameters <CRD>
Related Commands PULS:COUN PULS:DCYC PULS:PER PULS:WIDT
- MX / RS Series 1
- SCPI Programming Manual 1
- 2 MX / RS Series 2
- MX / RS Series 5 5
- SAFETY SYMBOLS 5
- Warranty Period: 1 Year 6
- WARRANTY TERMS 6
- PRODUCT RETURN PROCEDURE 6
- Table of Contents 7
- MX / RS Series 9 9
- Introduction 10
- External References 11
- Introduction to Programming 11
- Introduction to SCPI 13
- Types of SCPI Messages 14
- The SCPI Command Tree 14
- Using Queries 16
- Structure of a SCPI Message 16
- The Message Unit 16
- Combining Message Units 17
- Headers 18
- Query Indicator 18
- Message Unit Separator 18
- Root Specifier 19
- Message Terminator 19
- SCPI Data Formats 20
- Numerical Data Formats 20
- Character Data 20
- GPIB Controllers 21
- Agilent 82350 Driver 21
- RS232C Interface 23
- Serial Cable Diagram 24
- USB Interface 25
- USB Driver Installation 25
- MX / RS Series 31 31
- USB Interface Use 33
- LAN Interface Option 34
- MAC Address 34
- Setting the TCP/IP Address 34
- Socket Port Number 36
- IP Ping 36
- SCPI Command Reference 37
- Calibration Subsystem 38
- [:SOURce] 39
- :HRANge 39
- :IMPedance 39
- Password 40
- Current Measurement 41
- Voltage Measurement 43
- Output Phase 45
- Output - AC Voltage 46
- Output - DC Voltage 48
- Display Subsystem 50
- Instrument Subsystem 52
- Current Array Data 55
- 58 MX / RS Series 58
- Voltage Array Data 59
- Phase Measurement Subsystem 66
- Power Measurement Subsystem 67
- Output Subsystem 72
- Output Relay 72
- Output Protection 73
- Output Remote Inhibit Modes 73
- External Trigger Output 75
- Source Subsystem - Current 78
- Source Subsystem - Frequency 80
- Source Subsystem - Limit 85
- Source Subsystem - List 89
- List - Count 90
- List - Dwell 90
- List - Frequency 91
- List - Repeat 93
- List - Step 93
- List:TTL Trigger Out 94
- List:Voltage 95
- Source Subsystem - Mode 97
- Source Subsystem - Phase 98
- Source Subsystem - PONSetup 99
- Source Subsystem - Pulse 103
- Source Subsystem - Voltage 106
- Status Subsystem Commands 111
- System Commands 115
- Trigger Subsystem 123
- Common Commands 128
- 5.1 *CLS 129
- 5.2 *ESE 130
- 5.3 *ESR? 130
- 5.4 *IDN? 131
- 5.5 *OPC 131
- 5.6 *OPT? 132
- 5.7 *PSC 133
- 5.8 *RCL 133
- 5.9 *RST 134
- 5.10 *SAV 135
- 5.11 *SRE 135
- 5.12 *STB? 136
- 5.13 *TRG 137
- 5.14 *WAI 137
- Programming Examples 138
- Programming the Output 139
- Power-on Initialization 139
- Enabling the Output 139
- AC Voltage and Frequency 139
- Programming the Output Phase 141
- Current Limit 141
- Waveform Shapes 142
- Individual Phases 143
- Coupled Commands 144
- FIXED mode 146
- STEP mode 146
- PULSE mode 146
- LIST mode 146
- Step and Pulse Transients 147
- List Transients 148
- Triggering Output Changes 150
- Trigger System Model 150
- Generating Triggers 152
- Acquiring Measurement Data 153
- Power Measurements 154
- Frequency Measurements 154
- Harmonic Measurements 155
- Triggering Measurements 156
- TRIGGER RECEIVED 157
- INIT[:IMM]:ACQ 157
- 4096 DATA POINTS 160
- Trigger System Summary 161
- Status Registers 162
- Questionable Status Group 165
- Standard Event Status Group 166
- Status Byte Register 166
- Examples 167
- SCPI Command Completion 168
- Option Commands 169
- IEC 1000-4-11 (-411) 170
- IEC 1000-4-13 (-413) 174
- IEC 1000-4-13 Subsystem 174
- Interharmonics Subsystem 185
- RTCA/DO-160D (-160) 187
- VOLTAGE SURGE, for detail 189
- VOLTAGE UNDER 189
- MIL-STD 704E (-704) 194
- AC System 194
- DC System 195
- Programming Considerations 195
- OMNI Reference Impedance 197
- Watt Hour Meter (-WHM) 198
- Current Sink Option (-SNK) 199
- 202 MX / RS Series 202
- MX / RS Series 209 209
- SCPI Version 209
- Appendix C: Error Messages 210
- MX / RS Series 211 211
- 212 MX / RS Series 212
- MX / RS Series 213 213
- 214 MX / RS Series 214
- MX / RS Series 215 215
- Table 8-4 : Error Messages 215
Relacionado con productos y manuales para De medición, control y control California Instruments 801RP Series
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales