California Instruments 2253iX Manual de instrucciones Pagina 12
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming Manual Compact i / iX Series
AMETEK Programmable Power Division 12
1.4.2 USB Capabilities of the AC source
All AC source functions are programmable over the USB interface. The USB capabilities of the
AC source are listed in Chapter 2 of the User's Manual. Some capabilities support on the GPIB
interface such as ATN, GET and SRQ interrupts do not apply to the USB interface. The USB
interface operates internally at a fixed baudrate of 460800 baud but USB 2.0 burst transfer rates
are supported.
To set up the USB interface on a Windows XP PC, refer to section 3.2, “ USB Interface”.
The USB interface may be used to install updated firmware for the power source controller if
needed. Firmware updates and a Flash Loader utility program and instructions are available from
the AMETEK Programmable Power website for this purpose. (www.programmablepower.com
)
Multiple USB connections to same PC:
The Windows driver used to interface to the power source’s USB port emulates a serial com port.
This virtual com port driver is unable to reliable differentiate between multiple units however so
the use of more than one AC power source connected to the same PC via USB is not
recommended. Use of the GPIB interface is recommended for these situations.
1.4.3 RS232 Capabilities of the AC source
Only 2253i and 2253iX models are furnished with a DB9 pin RS232 interface. All AC source
functions are programmable over the RS232 interface. The RS232 capabilities of the AC source
are listed in Chapter 2 of the User's Manual. Some capabilities support on the GPIB interface
such as ATN, GET and SRQ interrupts do not apply to the RS232 interface. The RS232 interface
operates at baudrates between 9600 and 115200 baud.
The RS232 interface may be used to install updated firmware for the power source controller if
needed. Firmware updates and a Flash Loader utility program and instructions are available from
the AMETEK Programmable Power website for this purpose. (www.programmablepower.com
)
1.4.4 LAN Capabilities of the AC source
The –LAN option is only available on iX models. All AC source functions are programmable over
the LAN (Ethernet) interface if the –LAN option is installed. The LAN capabilities of the AC source
are listed in Chapter 2 of the User's Manual. Some capabilities support on the GPIB interface
such as ATN, GET and SRQ interrupts do not apply to the LAN interface. The LAN interface
operates internally at a fixed baudrate of 460800 baud but autodetection of 10Base-T, 100Base-T
and 1000Base-T is supported.
To set up the LAN interface on a Windows XP PC, refer to section 3.3.
- Compact i/iX 1
- AC and DC Power Source 1
- Programming Manual 1
- WARNING 4
- WARRANTY TERMS 5
- PRODUCT RETURN PROCEDURE 5
- 1. Introduction 9
- 1.2.1 Phase Selection 10
- 1.2.2 Firmware differences 10
- 1.2.3 Hardware differences 10
- 2. Introduction to SCPI 13
- 2.2.3 The SCPI Command Tree 14
- 2.3 Using Queries 16
- 2.4 Coupled Commands 16
- 2.5.3 Headers 17
- 2.5.4 Query Indicator 18
- 2.5.6 Root Specifier 18
- 2.5.7 Message Terminator 18
- 2.6 SCPI Data Formats 19
- 3. System Considerations 20
- 3.2 USB Interface 21
- 3.2.2 USB Interface Use 27
- 3.3 RS232 Interface 28
- 3.4 LAN Option 28
- 3.4.5 Socket Port Number 32
- 4. SCPI Command Reference 33
- 4.2 Subsystem Commands 34
- 4.3 Calibration Subsystem 35
- 4.4 Diagnostic Subsystem 37
- 4.5 Display Subsystem 38
- 4.6 Instrument Subsystem 40
- 4.7 Limit Subsystem 41
- 4.13 Output Subsystem 60
- 4.14 Power On Subsystem 64
- 4.25 System Commands 101
- 4.27 Trigger Subsystem 109
- (default) 110
- 5. Common Commands 114
- 5.1 *CLS 115
- 5.2 *ESR? 116
- 5.3 *IDN? 116
- 5.4 *OPC 116
- 5.5 *OPT? 117
- 5.6 *PSC 117
- 5.7 *RCL 118
- 5.8 *RST 119
- 5.9 *SAV 120
- 5.10 *SRE 120
- 5.11 *STB? 121
- 5.12 *TRG 121
- 5.13 *TST? 121
- 5.14 *WAI 122
- 6. Programming Examples 123
- 6.2.1 Waveform Shapes 125
- 6.2.2 Individual Phases 126
- 6.3 Coupled Commands 127
- 6.6 List Transients 132
- 6.7.7 Generating Triggers 137
- 6.8 Making Measurements 138
- 6.8.2 Power Measurements 139
- 6.8.3 Harmonic Measurements 139
- 6.10.2 Download Sample 148
- 7.1 Power-On Conditions 150
- 7.2 Operation Status Group 150
- 7.6 Status Byte Register 156
- 7.7 Examples 157
- 7.8.1 Remote Inhibit (RI) 160
- 7.9 SCPI Command Completion 161
- 8. Option Commands 162
- 8.2 RTCA/DO-160D (-160) 163
- VOLTAGE SURGE, for details 165
- 8.3.1 Command Tree 170
- 8.4.1 Command Tree 177
- 8.9.1 Introduction 194
- 8.9.2 ABLE Language details 195
- 8.9.3 Language Extension 198
- 8.10 Watt Hour Meter (-WHM) 199
- Appendix C : Error Messages 207
Relacionado con productos y manuales para De medición, control y control California Instruments 2253iX
(156 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales