California Instruments 2253iX Manual de instrucciones Pagina 211
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming Manual Compact i / iX Series
AMETEK Programmable Power Division 211
Number Message String Cause Remedy
815 "Slew time exceed dwell" Time needed to slew
to final value is less
than dwell time.
Check dwell times in transient list
settings. Increase dwell time or change
slew rate for affected parameter.
816 "Illegal during transient" Operation requested
not available while
transient is running.
Wait till transient execution is completed
or abort transient execution first.
817 "Output relay must be
closed"
Transient
programmed with
output relay open.
Close relay before attempting transient
operation.
819 "Clock and sync must be
internal"
Operation not
possible with external
clock
Switch to internal sync. (Default)
820 "Input buffer full" Too much data
received.
Break up data in smaller blocks.
821 "PFC Input Fault " AC input line related
error.
Possibly due to low line input condition
requiring too much input current.
822 "Waveform harmonics
limit"
Harmonic contents of
user defined wave
shape is too high and
could damage
amplifier output
stage.
Reduce harmonic content or reduce
fundamental frequency programmed.
823 "Amplifier fault" An amplifier failure.
Can be reported at
any time.
Determine which amplifier is at fault with
self-test or checking LED on Relay
Board. Replace amplifier.
824 “Output relay must be
open”
Operation requested
not possible with
relay state closed.
Generaly caused by trying to change
voltage range while output relay is
closed. Open relay first, then voltage
range can be changed.
825 “Over voltage prot trip” Over voltage
detected on output
Check output voltage for correct RMS
value.
826 “Peak current prot trip” Peak current limit
exceeded.
Peak current exceeded. Could be
caused by switching EUT on or off.
827 “Frequency error” Frequency error
during self-test.
Correct frequency was not measured
during self-test. May be result of 801
error.
828 “Phase error” Self test error phase
angle
Correct phase angle was not measured
during self-test. May be result of 801
error.
829 “Dc component exceed
limit”
Too much DC content
in loaded ARB
waveform.
Check waveform programming.
Table 8-3: SCPI error codes and messages.
- Compact i/iX 1
- AC and DC Power Source 1
- Programming Manual 1
- WARNING 4
- WARRANTY TERMS 5
- PRODUCT RETURN PROCEDURE 5
- 1. Introduction 9
- 1.2.1 Phase Selection 10
- 1.2.2 Firmware differences 10
- 1.2.3 Hardware differences 10
- 2. Introduction to SCPI 13
- 2.2.3 The SCPI Command Tree 14
- 2.3 Using Queries 16
- 2.4 Coupled Commands 16
- 2.5.3 Headers 17
- 2.5.4 Query Indicator 18
- 2.5.6 Root Specifier 18
- 2.5.7 Message Terminator 18
- 2.6 SCPI Data Formats 19
- 3. System Considerations 20
- 3.2 USB Interface 21
- 3.2.2 USB Interface Use 27
- 3.3 RS232 Interface 28
- 3.4 LAN Option 28
- 3.4.5 Socket Port Number 32
- 4. SCPI Command Reference 33
- 4.2 Subsystem Commands 34
- 4.3 Calibration Subsystem 35
- 4.4 Diagnostic Subsystem 37
- 4.5 Display Subsystem 38
- 4.6 Instrument Subsystem 40
- 4.7 Limit Subsystem 41
- 4.13 Output Subsystem 60
- 4.14 Power On Subsystem 64
- 4.25 System Commands 101
- 4.27 Trigger Subsystem 109
- (default) 110
- 5. Common Commands 114
- 5.1 *CLS 115
- 5.2 *ESR? 116
- 5.3 *IDN? 116
- 5.4 *OPC 116
- 5.5 *OPT? 117
- 5.6 *PSC 117
- 5.7 *RCL 118
- 5.8 *RST 119
- 5.9 *SAV 120
- 5.10 *SRE 120
- 5.11 *STB? 121
- 5.12 *TRG 121
- 5.13 *TST? 121
- 5.14 *WAI 122
- 6. Programming Examples 123
- 6.2.1 Waveform Shapes 125
- 6.2.2 Individual Phases 126
- 6.3 Coupled Commands 127
- 6.6 List Transients 132
- 6.7.7 Generating Triggers 137
- 6.8 Making Measurements 138
- 6.8.2 Power Measurements 139
- 6.8.3 Harmonic Measurements 139
- 6.10.2 Download Sample 148
- 7.1 Power-On Conditions 150
- 7.2 Operation Status Group 150
- 7.6 Status Byte Register 156
- 7.7 Examples 157
- 7.8.1 Remote Inhibit (RI) 160
- 7.9 SCPI Command Completion 161
- 8. Option Commands 162
- 8.2 RTCA/DO-160D (-160) 163
- VOLTAGE SURGE, for details 165
- 8.3.1 Command Tree 170
- 8.4.1 Command Tree 177
- 8.9.1 Introduction 194
- 8.9.2 ABLE Language details 195
- 8.9.3 Language Extension 198
- 8.10 Watt Hour Meter (-WHM) 199
- Appendix C : Error Messages 207
Relacionado con productos y manuales para De medición, control y control California Instruments 2253iX
(156 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales