California Instruments 2253iX Manual de instrucciones Pagina 209
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming Manual Compact i / iX Series
AMETEK Programmable Power Division 209
Number Message String Cause Remedy
-255 “Directory full” Too many waveform
directory entries
Delete one or more waveforms from
waveform memory to make room.
-256 “File name not found” Waveform requested
not in directory
Check waveform directory for waveform
names present.
-257 “File name error” Incorrect filename Too many or non ASCII characters used
in waveform file definition.
-283 “Illegal variable name” Variable name illegal. Use ASCII characters only
-300 "Device specific error" Hardware related
error
Check hardware for proper operation.
-311 "Memory error" Waveform memory
checksum error.
May be the result of incomplete user-
defined waveform download. Check
interface and try downloading waveform
again. Successful download may clear
this error condition.
Alternatively, use TRAC:DEL:ALL
command to clear waveform memory.
-314 "Save/recall memory
lost"
User setup register
contents lost
Store setup in same register again.
-315 "Configuration memory
lost"
Hardware
configuration settings
lost.
Contact CI service department at
to obtain
instructions on restoring configuration
data.
-330 "Self-test failed" Internal error Contact CI service department at
-350 "Queue overflow" Message queue full. Too many message. Read status using
SYST:ERR query until 0, "No Error" is
received indicating queue empty.
-400 "Query error" Unable to complete
query.
Check programming manual for correct
query format and parameters
-410 "Query INTERRUPTED" Query issued but
response not read.
Check application program for correct
flow. Response must be read after each
query to avoid this error.
-420 "Query
UNTERMINATED"
Query incomplete. Check for terminator after query
command.
-430 "Query DEADLOCKED" Query cannot be
completed
Check application program for multiple
queries
-440 "Query
UNTERMINATED"
Query incomplete. Check for terminator after query
command.
0 "No error" No errors in queue
40 "Voltage self test error,
output 1”
No. 1/A amplifier in
Master source has no
or incorrect output
voltage during Self-
test.
Contact CI service department at
41 "Voltage self test error,
output 2”
No. 2/B amplifier in
Master source has no
or incorrect output
voltage during Self-
test. Three phase
models only.
Contact CI service department at
42 "Voltage self test error, No. 3/C amplifier in Contact CI service department at
- Compact i/iX 1
- AC and DC Power Source 1
- Programming Manual 1
- WARNING 4
- WARRANTY TERMS 5
- PRODUCT RETURN PROCEDURE 5
- 1. Introduction 9
- 1.2.1 Phase Selection 10
- 1.2.2 Firmware differences 10
- 1.2.3 Hardware differences 10
- 2. Introduction to SCPI 13
- 2.2.3 The SCPI Command Tree 14
- 2.3 Using Queries 16
- 2.4 Coupled Commands 16
- 2.5.3 Headers 17
- 2.5.4 Query Indicator 18
- 2.5.6 Root Specifier 18
- 2.5.7 Message Terminator 18
- 2.6 SCPI Data Formats 19
- 3. System Considerations 20
- 3.2 USB Interface 21
- 3.2.2 USB Interface Use 27
- 3.3 RS232 Interface 28
- 3.4 LAN Option 28
- 3.4.5 Socket Port Number 32
- 4. SCPI Command Reference 33
- 4.2 Subsystem Commands 34
- 4.3 Calibration Subsystem 35
- 4.4 Diagnostic Subsystem 37
- 4.5 Display Subsystem 38
- 4.6 Instrument Subsystem 40
- 4.7 Limit Subsystem 41
- 4.13 Output Subsystem 60
- 4.14 Power On Subsystem 64
- 4.25 System Commands 101
- 4.27 Trigger Subsystem 109
- (default) 110
- 5. Common Commands 114
- 5.1 *CLS 115
- 5.2 *ESR? 116
- 5.3 *IDN? 116
- 5.4 *OPC 116
- 5.5 *OPT? 117
- 5.6 *PSC 117
- 5.7 *RCL 118
- 5.8 *RST 119
- 5.9 *SAV 120
- 5.10 *SRE 120
- 5.11 *STB? 121
- 5.12 *TRG 121
- 5.13 *TST? 121
- 5.14 *WAI 122
- 6. Programming Examples 123
- 6.2.1 Waveform Shapes 125
- 6.2.2 Individual Phases 126
- 6.3 Coupled Commands 127
- 6.6 List Transients 132
- 6.7.7 Generating Triggers 137
- 6.8 Making Measurements 138
- 6.8.2 Power Measurements 139
- 6.8.3 Harmonic Measurements 139
- 6.10.2 Download Sample 148
- 7.1 Power-On Conditions 150
- 7.2 Operation Status Group 150
- 7.6 Status Byte Register 156
- 7.7 Examples 157
- 7.8.1 Remote Inhibit (RI) 160
- 7.9 SCPI Command Completion 161
- 8. Option Commands 162
- 8.2 RTCA/DO-160D (-160) 163
- VOLTAGE SURGE, for details 165
- 8.3.1 Command Tree 170
- 8.4.1 Command Tree 177
- 8.9.1 Introduction 194
- 8.9.2 ABLE Language details 195
- 8.9.3 Language Extension 198
- 8.10 Watt Hour Meter (-WHM) 199
- Appendix C : Error Messages 207
Relacionado con productos y manuales para De medición, control y control California Instruments 2253iX
(156 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.013 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales