California Instruments 2253iX Manual de instrucciones Pagina 96
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming Manual Compact i / iX Series
AMETEK Programmable Power Division 96
STATus:OPERation:NTR STATus:OPERation:PTR
These commands set or read the value of the Operation NTR (Negative-Transition) and PTR
(Positive-Transition) registers. These registers serve as polarity filters between the Operation
Enable and Operation Event registers to cause the following actions:
• When a bit in the Operation NTR register is set to 1, then a 1-to-0 transition of the
corresponding bit in the Operation Condition register causes that bit in the Operation Event
register to be set.
• When a bit of the Operation PTR register is set to 1, then a 0-to-1 transition of the
corresponding bit in the Operation Condition register causes that bit in the Operation Event
register to be set.
• If the same bits in both NTR and PTR registers are set to 1, then any transition of that bit at
the Operation Condition register sets the corresponding bit in the Operation Event register.
• If the same bits in both NTR and PTR registers are set to 0, then no transition of that bit at
the Operation Condition register can set the corresponding bit in the Operation Event
register.
Note: Setting a bit in the PTR or NTR filter can of itself generate positive or negative events in
the corresponding Operation Event register.
Command Syntax STATus:OPERation:NTRansition<NRf+>
STATus:OPERation:PTRansition<NRf+>
Parameters 0 to 32727
Default Value 0
Examples STAT:OPER:NTR 32 STAT:OPER:PTR 1
Query Syntax STATus:OPERation:NTR?
STATus:OPERation:PTR?
Returned Parameters <NR1>(Register value)
Related Commands STAT:OPER:ENAB
Bit
Position
15 14 13 12 11 10 9 8-5 4 3 2 1 0
Bit Name
not
used
not
used
Isum CL
rms
Rail not
used
RI not
used
TO UNR not
use
d
OCP OV
Bit Weight
8192 4096 2048 512 16 8 2 1
Table 4-4: Bit Configuration of Questionable Registers
OV over-voltage protection has tripped
OCP over-current protection has tripped
UNR output is unregulated
TO over-temperature protection has tripped
RI remote inhibit is active
Rail loss of input phase detected
CL rms rms current limit is active
Isum summary of Isum registers
- Compact i/iX 1
- AC and DC Power Source 1
- Programming Manual 1
- WARNING 4
- WARRANTY TERMS 5
- PRODUCT RETURN PROCEDURE 5
- 1. Introduction 9
- 1.2.1 Phase Selection 10
- 1.2.2 Firmware differences 10
- 1.2.3 Hardware differences 10
- 2. Introduction to SCPI 13
- 2.2.3 The SCPI Command Tree 14
- 2.3 Using Queries 16
- 2.4 Coupled Commands 16
- 2.5.3 Headers 17
- 2.5.4 Query Indicator 18
- 2.5.6 Root Specifier 18
- 2.5.7 Message Terminator 18
- 2.6 SCPI Data Formats 19
- 3. System Considerations 20
- 3.2 USB Interface 21
- 3.2.2 USB Interface Use 27
- 3.3 RS232 Interface 28
- 3.4 LAN Option 28
- 3.4.5 Socket Port Number 32
- 4. SCPI Command Reference 33
- 4.2 Subsystem Commands 34
- 4.3 Calibration Subsystem 35
- 4.4 Diagnostic Subsystem 37
- 4.5 Display Subsystem 38
- 4.6 Instrument Subsystem 40
- 4.7 Limit Subsystem 41
- 4.13 Output Subsystem 60
- 4.14 Power On Subsystem 64
- 4.25 System Commands 101
- 4.27 Trigger Subsystem 109
- (default) 110
- 5. Common Commands 114
- 5.1 *CLS 115
- 5.2 *ESR? 116
- 5.3 *IDN? 116
- 5.4 *OPC 116
- 5.5 *OPT? 117
- 5.6 *PSC 117
- 5.7 *RCL 118
- 5.8 *RST 119
- 5.9 *SAV 120
- 5.10 *SRE 120
- 5.11 *STB? 121
- 5.12 *TRG 121
- 5.13 *TST? 121
- 5.14 *WAI 122
- 6. Programming Examples 123
- 6.2.1 Waveform Shapes 125
- 6.2.2 Individual Phases 126
- 6.3 Coupled Commands 127
- 6.6 List Transients 132
- 6.7.7 Generating Triggers 137
- 6.8 Making Measurements 138
- 6.8.2 Power Measurements 139
- 6.8.3 Harmonic Measurements 139
- 6.10.2 Download Sample 148
- 7.1 Power-On Conditions 150
- 7.2 Operation Status Group 150
- 7.6 Status Byte Register 156
- 7.7 Examples 157
- 7.8.1 Remote Inhibit (RI) 160
- 7.9 SCPI Command Completion 161
- 8. Option Commands 162
- 8.2 RTCA/DO-160D (-160) 163
- VOLTAGE SURGE, for details 165
- 8.3.1 Command Tree 170
- 8.4.1 Command Tree 177
- 8.9.1 Introduction 194
- 8.9.2 ABLE Language details 195
- 8.9.3 Language Extension 198
- 8.10 Watt Hour Meter (-WHM) 199
- Appendix C : Error Messages 207
Relacionado con productos y manuales para De medición, control y control California Instruments 2253iX
(156 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales