California Instruments 2253iX Manual de instrucciones Pagina 87
- Pagina / 216
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Programming Manual Compact i / iX Series
AMETEK Programmable Power Division 87
4.23 Source Subsystem - Voltage
This subsystem programs the output voltage of the i/iX Series AC source.
Subsystem Syntax
[SOURce:]
VOLTage
:ALC
[:STATe] ON | OFF | REG Sets Auto Level Control to on (trip), off, or regulation
:SOURce INTernal | EXTernal Sets voltage sense source
[:LEVel]
[:IMMediate]
[:AMPLitude]
[:AC] <n> Sets the ac rms voltage amplitude in AC mode
:DC <n> Sets the dc voltage in DC mode
:OFFSet <n> Set the dc offset value in percent of AC rms
:TRIGgered
[:AMPLitude] <n> Sets the transient voltage amplitude
:MODE <mode> Sets the voltage mode (FIX|STEP|PULS|LIST)
:PROTection
[:LEVel] <n> Sets the overvoltage protection threshold
:RANGe <n> Sets the voltage range
:REFerance INTernal | EXTernal Set the voltage referance to internal or external(RPV)
:SENSe
[:SOURce] INTernal | EXTernal Sets voltage sense source
:SLEW
[:IMMediate] <n> | INFinity Sets the voltage slew rate
:MODE <mode> Sets voltage slew mode (FIX|STEP|PULS|LIST)
:TRIGgered <n> | INFinity Sets the transient voltage slew rate
VOLTage:ALC[:STATe]
These commands select the various auto level control (ALC) modes. The ALC mode uses the
voltage measurement feedback to more precisely regulate the output voltage. The following ALC
modes can be selected:
ON | 0 This enables the ALC trip mode. If the programmed voltage cannot be
maintained, the output is disabled (relay opens) and a 801 Voltage error
is generated.
OFF | 1 This disables the ALC mode.
REG | 2 This enables the ALC regulation mode. The output voltage is regulated
based on the readback voltage but if regulation cannot be maintained,
the output does not trip off. Instead, a status bit is set in the Event Status
register to indicate the AC source is out of regulation.
Note that the command format will take either alphanumeric or integer data but the query form
always returns numeric data (NR1).
Command Syntax [SOURce:]VOLTage:ALC[:STATe] <source>
Parameters ON | OFF | REG | 0 | 1 | 2
*RST Value REG
Examples VOLT:ALC ON
Query Syntax [SOURce:]VOLTage:ALC?
Returned Parameters <NR1>
Related Commands VOLT
- Compact i/iX 1
- AC and DC Power Source 1
- Programming Manual 1
- WARNING 4
- WARRANTY TERMS 5
- PRODUCT RETURN PROCEDURE 5
- 1. Introduction 9
- 1.2.1 Phase Selection 10
- 1.2.2 Firmware differences 10
- 1.2.3 Hardware differences 10
- 2. Introduction to SCPI 13
- 2.2.3 The SCPI Command Tree 14
- 2.3 Using Queries 16
- 2.4 Coupled Commands 16
- 2.5.3 Headers 17
- 2.5.4 Query Indicator 18
- 2.5.6 Root Specifier 18
- 2.5.7 Message Terminator 18
- 2.6 SCPI Data Formats 19
- 3. System Considerations 20
- 3.2 USB Interface 21
- 3.2.2 USB Interface Use 27
- 3.3 RS232 Interface 28
- 3.4 LAN Option 28
- 3.4.5 Socket Port Number 32
- 4. SCPI Command Reference 33
- 4.2 Subsystem Commands 34
- 4.3 Calibration Subsystem 35
- 4.4 Diagnostic Subsystem 37
- 4.5 Display Subsystem 38
- 4.6 Instrument Subsystem 40
- 4.7 Limit Subsystem 41
- 4.13 Output Subsystem 60
- 4.14 Power On Subsystem 64
- 4.25 System Commands 101
- 4.27 Trigger Subsystem 109
- (default) 110
- 5. Common Commands 114
- 5.1 *CLS 115
- 5.2 *ESR? 116
- 5.3 *IDN? 116
- 5.4 *OPC 116
- 5.5 *OPT? 117
- 5.6 *PSC 117
- 5.7 *RCL 118
- 5.8 *RST 119
- 5.9 *SAV 120
- 5.10 *SRE 120
- 5.11 *STB? 121
- 5.12 *TRG 121
- 5.13 *TST? 121
- 5.14 *WAI 122
- 6. Programming Examples 123
- 6.2.1 Waveform Shapes 125
- 6.2.2 Individual Phases 126
- 6.3 Coupled Commands 127
- 6.6 List Transients 132
- 6.7.7 Generating Triggers 137
- 6.8 Making Measurements 138
- 6.8.2 Power Measurements 139
- 6.8.3 Harmonic Measurements 139
- 6.10.2 Download Sample 148
- 7.1 Power-On Conditions 150
- 7.2 Operation Status Group 150
- 7.6 Status Byte Register 156
- 7.7 Examples 157
- 7.8.1 Remote Inhibit (RI) 160
- 7.9 SCPI Command Completion 161
- 8. Option Commands 162
- 8.2 RTCA/DO-160D (-160) 163
- VOLTAGE SURGE, for details 165
- 8.3.1 Command Tree 170
- 8.4.1 Command Tree 177
- 8.9.1 Introduction 194
- 8.9.2 ABLE Language details 195
- 8.9.3 Language Extension 198
- 8.10 Watt Hour Meter (-WHM) 199
- Appendix C : Error Messages 207
Relacionado con productos y manuales para De medición, control y control California Instruments 2253iX
(156 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales